Tabletop Thread Catchers

Friday night was Material Girls at Pins & Needles. After a delicious dinner & show-n-tell, we made thread catchers. The pattern was from Red Hen Fabrics. 

 

The really neat thing about these catchers is that they fold down for easy 

transport.

   
Just twist and push down. The bottom slides into the top ring.

  
  

This is what it looks like in its compact state.

We made two changes to the pattern: cutting the cardboard circles and batting at 4" instead of 3 7/8" (cut your fabric circles at 5") and substituting package strapping for the 4” wooden embroidery hoop. Here is how to do that.

  Mark a piece of strapping at 13 inches.

Cut the strap approximately 3/8" beyond the mark. Cut a second piece of strapping the same length as the first. 

Overlap the first strap so that the unmarked end meets the marked line. 

Using duct tape, secure the overlapped ends. This creates the inside circle.

Center the second strapping piece over the joined ends of the circle. Tape in place. 

Keeping the second strap snug against the first, securely tape one end of the outside ring in place. 

  Bring the other end around to meet the first.

Secure  with tape. You now 
have a "recycled" hoop.

Til next time,
Mary

Napkins and a Bib

    My mom will be 88 years old next month. She is an independent lady who lives by herself, drives to all her necessary destinations, and crochets blankets and shawls to support ministries at her church. So, when she asked me for an adult bib, how could I say no? I couldn't. To the Google, where I found a pattern . I then decided she should have coordinating napkins to go with her bib. These are my directions for 18" square napkins, which require 1 1/8 yards of fabric.

   For each napkin, cut a 19" square. 

   Since, I prewash all my fabrics, I give my squares a good dosing of starch, both sides. This is to reduce stretching when I draw my lines. I wanted lines 1/2" from the outside edge on all four sides. My Quarter Inch Seam Marker is 1/2" wide, so it is perfect for my lines. 

   After marking the sides, the lines should cross at the corners.

 To reduce bulk in the corners, I trim off the point. But how much? After some trial and error, I discovered that my Quarter Square Triangle ruler did the job. Align the dashed 1/4" seam lines atop of the drawn lines.

 Trim straight across the blunt tip. 

 Fold over the corner with the fold at the intersection of the drawn lines(white X). Press, dab with some starch, and press again. Repeat for all four corners.

 Fold the sides up to the drawn lines and press. I use my stiletto to hold the fabric so as not to burn my fingers. As with the corners, I dab starch on the folds and press again.

 This is what my napkins look like after the first turnover.

For the second fold, I begin at the corner. Fold up each side to meet in a 45 degree angle. Press, dab with starch, press again. Repeat for the remaining corners. Press sides, easing as may be necessary to have a straight edge. Dab with starch and press. 

 Stitch the seam at a consistent distance from the edge, making sure to catch the inside fold.

   This is Mom's reversible bib and coordinating napkins.

And this is Mom :)

Til next time,

Mary

Machine Needle Threaders

  Before I begin today's topic, I wanted to share my s-l-o-w progress on Orca Bay.

Rows 1&2 and 3&4 were sewn together. Matching seams and easing in the geese takes time.It does look striking when seen though the camera.

  Many new sewing machines come with automatic needle threaders, which are terrific inventions. However, of the half dozen machines that I own, only one has it. Fortunately, relatively inexpensive machine needle threaders are available. They are portable and can be used on any machine.

These are three types of machine needle threaders that I own. 

All of them work they same way.

This is a close up of the Dritz brand. 

Hidden inside of the white end is a thin flat metal bar.

 This bar is what pushes the thread through the eye of the needle. 

Be careful not to bend the bar, as that will make it non-functional.

Notice the triangle on the blue part. It must face up(vertical) when threading the threader.

 Lay the thread horizontally through the teeth of the threader.

Lightly hold each side of the thread as you place the threader around the needle,

 keeping that triangle facing up.

Gently add pressure to the blue cylinder as you slide it down the shaft towards the eye of the needle. When the eye is reached, the thin metal bar pushes the thread through it. With smaller size needles, I place my finger on the right side of the needle for support(left side for featherweights).

Using my stiletto, I pull the thread through the needle. 

I am now ready to sew.

                        

The threaders I own also have holders for inserting a new needle in your machine.

I can still thread most front facing needles without much trouble. However, side threading machines and/or smaller needles are a different story. Especially my featherweight, which threads right to left. Using these needle threaders, I can thread a machine with my eyes closed. Not that I want to :)

Til next time,

Mary

The New Smaller Big Board

There was no sewing to be done yesterday. Instead, I read a book, Intimate Strangers by Laura Taylor, on my HP Touchpad. So, I thought today I would post some photos of my New Smaller Big Board(NSBB).

 

   This is my original large pressing surface. Made from an old hollow core luan door(salvaged from our home in NJ), covered with a blanket, some Insul Brite, and several layers of muslin, it had served me well for almost 15 years. When I originally made it, I was making home decorating items that used fabric 54" to 60" wide. A surface 30" wide was perfect then. Now, I wanted a narrower more portable pressing surface to attach to my wide ironing board.
   Off to Home Depot! I found the perfect base, 1"x 3" boards laminated together, 23" wide by 6 feet long. I could have used 3/4" plywood, but then I would have to cut it in half lengthwise.Short crosswise cuts are doable, but we don't have the set up for those long straight cuts. Not to mention, it wouldn't fit in my Sonata, which the laminate would. I also purchased 2- 1"x3" x 6' boards to use a cleats.

   This is the underside view of my NSBB. There are several tutorials on the web for how to make one. I read several, then modified to meet my needs. The board is not permanently attached, but I can fold up the unit for storage when needed. I can also adjust the height if I want to sit while pressing many pieces.

    Originally, I had placed it in front of my design wall. Notice the narrow space between the pressing board and cutting station. This was before I replaced the back legs on the table so, it would sit partially on the hearth. That opened some floor space,but more was needed. Especially, if I wanted friends to come to sew.

   So, I moved it to the fabric nook. The NSBB extends a bit into the bookcase, but I have access to the fabric and storage bins. The overhead light and iron are plugged into the same power strip. I know the iron is off if the light is off. 

  Wes came last Sunday to test drive my new space. It worked well and we had a good time working on our projects.

Til next time,

Mary 

Progress on Orca Bay

   I love my new work space. It inspires me to work on projects that have been tucked away for months.I can't say years as I've only been quilting for 6 years. 

   These are some of the pieces for Orca Bay , set out to be sewn. After I took the photo, I realized that every other set of geese should be flying in the opposite direction. Otherwise, the wouldn't have the right effect.

   The geese should all fly towards the light background Ohio Star blocks. I have sewn all these into rows, which I am hoping to assemble today. Next, will be the borders.

   During our visit to Wisconsin in June, my cousin Karen gave me a cute pincushion. It sits next to Frances, my first Husqvarna/Viking sewing machine. The pincushion is perfect. It holds a ton of pins, a small pair of scissors, and  stilettos between the petals. 

Til next time,

Mary

   

Back to Sewing

In the midst of all the redoing and building, I have managed to work on some projects. 

  Last week, Carol and I did some wool applique. I am new to this form quilting/sewing. The first one had die cut pieces, but this one I had to cut my own. I selected a project from the book Pennies from Heaven. I like the embroidery around the center, but the green looks a bit empty. Wool definitely has a nice feel to it.

  The second project is an older block of the month called The Queen and Her Court from A Wing and A Prayer Design. I made block 1 in May(upper right), but didn't have a chance to do June(upper left) or July (lower right) til this week. Notice the difference in color palette from the pattern. I have also completed August, but not when I took this photo. I am now all caught up until September.

  Now I am returning to work on my Orca Bay. It was a Quiltville Mystery last winter that I convinced Carol to do with me. She has finished her top, mine is only half done. So, I am planning to have it completed by Thanksgiving. One year, start to finish.

Til next time,
Mary

Quilting Studio Redo- Phase 3

     Phase 3 was to rearrange the laundry room, creating a more organized and efficient space to store fabric.

    The laundry is to the left as you enter the quilting studio. It is a good size room, but not efficient. I have a front loading washer and dryer which until several days ago were not stacked.

    Most of my fat quarters were stored in between the wall studs to the left in the photo. Clutter again. On top of the washer and dryer is an old hollow core luan door which I covered to make a pressing surface. Straight back is another shelf unit to hold plastic bins full of mostly fabric scraps. I do love my scraps :) Have you ever noticed that every horizontal surface seems to attract stuff, on its way to being put away, of course.

    In preparation for stacking the W/D, I moved the pressing board to the top of the shelf unit, added a light, and cleaned up the fat quarters.This was not the best solution as it cut the room in half. Two small areas on each side of the W/D.

    Once again, valuable real estate being squandered. So, DH and DS#1 stacked them for me. Another four square feet gained. Shifting the W/D as far to the left as possible created a small area to the left to store vertical items and my rolling cart of supplies, and to the right...

                                                           a very nice fabric nook. 

     Now, the bins with the fabric scraps are easily accessible and my yardage is neatly folded and stacked in a bookcase. This is a much better view from the main part of the studio than that in the first photo of this post. Another advantage, I can place my new big board in this area when I have others over to sew, freeing up space in the main area.

    To store fabric as I have, fold yardage in half lengthwise, the way it comes off the bolt. Wrap it around a 6" x 24" ruler, slip out the ruler, fold in half again lengthwise, and stack in the bookcase. This creates a uniform width and length to the fabric, which stores very nicely. To determine if there is enough fabric for a project, I count the layers, multiply by 6 then divide by 36 . No more unfolding all the fabric only to discover there isn't enough.

Til next time,

Mary